|
08-28-2015, 11:34 AM
|
#1
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
Slide out question
On my 2014 30re when I slide the slide out the wood trim (towards the rear of camper) moves a little like the slide out is going out to far. Is there an adjustment that came be made?
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
08-28-2015, 11:37 AM
|
#2
|
Site Team
Join Date: Sep 2012
Location: PA
Posts: 5,721
|
Had the same issue, my dealer made the adjustment.
__________________
Mark & Susan
Lehighton, Pennsylvania
EAGLE HT FIFTH WHEEL | 30.5CKTS - '13 Ford F150 SCREW - PullRite Superslide - Roadmaster Active Suspension
Member - "Northeast Adventures RV Rally Group" & "Mason-Dixon Bunch"
|
|
|
08-29-2015, 11:12 AM
|
#3
|
Full Time Camper
Join Date: Oct 2004
Location: Texas
Posts: 1,508
|
Per the Lippert slide out manual, there is a round silver can on a threaded rod, called a "stop can". Adjusting the position of the outer two nuts (the ones attached to the actual bracket on the slide-out will fix the problem.
Adjusting room so it seals in the OUT position
1. Locate actuator coming through the frame.
2. On the end of the actuator there is a threaded shaft mounted
to the bracket with 3 nuts and a stop can.
3. Move one of the 1” nuts (Jam Nut-2 or Nylock Nut) one way
or the other– this will change the location of your seal going
to the “out position”.
4. Make sure all nuts are tight.
__________________
Larry Day
Texas Baptist Men-Retiree Builders member since '01
13 Silverado 3500HD D/A, 2wd CCSB srw, custom RKI bed
11 Cruiser CF32MK
https://www.picturetrail.com/dayle1
|
|
|
09-08-2015, 12:03 PM
|
#4
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
Where is this threaded rod?
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
09-14-2015, 08:08 AM
|
#6
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
Hum I can't seem to find the adjuster, is it underneath? I dropped the cover some but couldn't find it. Didn't want to drop it completely until I found out it was under there
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
09-14-2015, 08:20 AM
|
#7
|
Site Team
Join Date: Dec 2007
Location: WI.
Posts: 9,160
|
Quote:
Originally Posted by Dayle1
Per the Lippert slide out manual, there is a round silver can on a threaded rod, called a "stop can". Adjusting the position of the outer two nuts (the ones attached to the actual bracket on the slide-out will fix the problem.
Adjusting room so it seals in the OUT position
1. Locate actuator coming through the frame.
2. On the end of the actuator there is a threaded shaft mounted
to the bracket with 3 nuts and a stop can.
3. Move one of the 1” nuts (Jam Nut-2 or Nylock Nut) one way
or the other– this will change the location of your seal going
to the “out position”.
4. Make sure all nuts are tight.
|
Quote:
Originally Posted by Dayle1
|
You shouldn't have to drop the membrane if you have the slide system Larry has the link to.
Just follow what the instructions stated.
|
|
|
09-14-2015, 08:24 AM
|
#8
|
Full Time Camper
Join Date: Apr 2006
Location: 1
Posts: 2,036
|
Do the newer slide systems have the same "stop can"?
|
|
|
09-14-2015, 07:24 PM
|
#9
|
Full Time Camper
Join Date: Oct 2004
Location: Texas
Posts: 1,508
|
Quote:
Originally Posted by Stan
Do the newer slide systems have the same "stop can"?
|
Crossroads switched to the Schwintek system a few yrs ago, then switched back to standard Lippert gear system. But different brands within CR probably didn't switch at the same time and model years are not a good identifier. If the slide out has two aluminum slotted guides on each side, then it is the Schwintek system. Otherwise, it should be the Lippert underfloor gear system.
__________________
Larry Day
Texas Baptist Men-Retiree Builders member since '01
13 Silverado 3500HD D/A, 2wd CCSB srw, custom RKI bed
11 Cruiser CF32MK
https://www.picturetrail.com/dayle1
|
|
|
09-14-2015, 07:46 PM
|
#10
|
Full Time Camper
Join Date: Jul 2006
Location: MS
Posts: 2,746
|
I think Larry I read some where that they have gone to the BAL cable system on some units.
__________________
Frank and Janet Henn
2000 Monoco Lapalma
being pushed by a 2004 Jeep Grand Cherokee
Traveling with Rainbow the wonder dog and now with Sunshine the rescue Schnauzer.
|
|
|
09-14-2015, 08:14 PM
|
#11
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
Mine has the aluminum worm looking guides, the slide out goes out to far on the front part, it's done got the wood trim loose on the rear from it going out to far. The first pic is the front second is the rear
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
09-14-2015, 08:15 PM
|
#12
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
See how the foam is smashed more on the front
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
09-14-2015, 08:17 PM
|
#13
|
Weekend Camper
Join Date: Aug 2015
Location: Mississippi
Posts: 90
|
Here's another pic of rear with foam lined up
__________________
mike
2014 sunset trail reserve 30re
2005 dodge 2500 diesel 4x4
Southaven Ms.
|
|
|
09-14-2015, 09:28 PM
|
#14
|
Seasonal Camper
Join Date: May 2014
Location: TX
Posts: 335
|
You have a Schwintek slide system. Here's a video to help re-time the system.
Good luck!
__________________
John (USAF Ret) & Cheryl
San Antonio, TX
2014 Hill Country 32FR
2011 Ram 2500 4x4 6.7 CTD
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|