Reply
 
Thread Tools Search this Thread Display Modes
 
Old 07-19-2012, 09:32 AM   #1
Weekend Camper
 
papabear9695's Avatar
 
Join Date: Jul 2012
Location: Florida
Posts: 18
We have a 2012 Sunset Trail with the exterior gas grill, which has a bracket on the rear bumper and a grill that was in the rear compartment. There is no instructions for the setup and use of the grill. After placing th grill on the bracket, I do not think it is the right grill for the bracket either. I took pictures of the grill and the bracket and sent it to the web site listed for questions and I have no answers to date. There is a gas line with a shut off valve below the door for the rear storage compartment on the side of the grill bracket. There is also a new gas hose with quick connections that is too short to reach the grill.

Can somebody please help me? We bought the trailer used from Lazy Days in Florida, so there is no dealer i can go back to. The trailer was originally purchased in Pennsylvania, and brought to Florida. It was never used and traded for a motor home.
papabear9695 is offline   Reply With Quote
Old 07-19-2012, 09:57 AM   #2
Weekend Camper
 
Big smokey's Avatar
 
Join Date: Mar 2012
Location: green cove sp
Posts: 49
When I purchased my camper I to found that the hose was to short. So i called the grill company and they told me the dealer was responsible for the hose. So I called them and they told me to come by and get a longer one. As far as the bracket it took me a little time to figure out how it went.Edited by: Big smokey
__________________
2012 ST30RK

2007 F250 super duty
Big smokey is offline   Reply With Quote
Old 07-20-2012, 11:39 AM   #3
Seasonal Camper
 
mnsunset's Avatar
 
Join Date: Feb 2012
Location: minnesota
Posts: 365
Can you post a pic of the grill and bracket fully extended so we can see if it is correct?





mnsunset is offline   Reply With Quote
Old 07-20-2012, 08:28 PM   #4
Weekend Camper
 
papabear9695's Avatar
 
Join Date: Jul 2012
Location: Florida
Posts: 18
I would love to attach the photos of the grill and the bumper bracket but it seems i have no ability at this time to post the images with this system. I would also like to know the manufacturer of the grill or brand name so I could get some instructions. So far I have been able to find nothing. Any and all help would be appreciated.
papabear9695 is offline   Reply With Quote
Old 07-22-2012, 01:37 PM   #5
Seasonal Camper
 
mnsunset's Avatar
 
Join Date: Feb 2012
Location: minnesota
Posts: 365
What is the length of your gas hose?





mnsunset is offline   Reply With Quote
Old 07-23-2012, 06:51 AM   #6
Weekend Camper
 
papabear9695's Avatar
 
Join Date: Jul 2012
Location: Florida
Posts: 18
The hose is 4 foot, 2 inches in length, with a male and female quick disconnects, one on each end.
papabear9695 is offline   Reply With Quote
Old 07-23-2012, 10:22 AM   #7
Seasonal Camper
 
mnsunset's Avatar
 
Join Date: Feb 2012
Location: minnesota
Posts: 365
I will try to get out and measure mine soon.





mnsunset is offline   Reply With Quote
Old 07-24-2012, 02:32 PM   #8
Seasonal Camper
 
mnsunset's Avatar
 
Join Date: Feb 2012
Location: minnesota
Posts: 365
Yup mine is the same length.
I measured from the rear side of the bumper to the gas hookup under the RV and it measures about 30 inches. So when the grill bracket is fully extended and locked into position, it reaches fine.





mnsunset is offline   Reply With Quote
Old 08-04-2012, 12:15 PM   #9
Weekend Camper
 
Djkell001's Avatar
 
Join Date: Jul 2012
Location: PA
Posts: 35
You have to extend the bracket until it is straight and then reinstall the the clip to hold it in place. The grill has 2 round pins going straight up this is where the grill sits on. Look at the grill you will see a round bracket on each side these slide over the upright round posts.
Djkell001 is offline   Reply With Quote
Old 08-05-2012, 01:10 AM   #10
Weekend Camper
 
papabear9695's Avatar
 
Join Date: Jul 2012
Location: Florida
Posts: 18
My grill has a bracket on each side that can slip over the vertical pins on the bracket. The problwm is, the grill is shorter than the distance between the two pins. Therefore, i can only slide the grill over one pin. There is a slot set on the bottom of the grill which should be for a grease receptor. of course the tray that i would consider for the gtrease receptor is not with the grill. Since i have no manufacturer of the grill or bracket, I can get no answers. Crossroads factory states this is the correct setup from my photos, but cannot supply me with any instructions or how to SAFELY make it work. Any help would be greatly appreciated.
papabear9695 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Crossroads RV or any of its affiliates. This is an independent, unofficial site.


All times are GMT -6. The time now is 07:40 AM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2019, vBulletin Solutions, Inc.