|
01-16-2021, 12:09 PM
|
#1
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
Motor synchronization location
I have a crossroads sunset trail reserve 32 rl it has 3 schwintech slideouts one in front bedroom and 2 in living are one with stove and fireplace and on for the dining and chair area. I located the small bedroom slide out controller in the compartment with the pump. Does anybody no were the controllers for the front 2 slideouts are located . I can't find them anywere .
|
|
|
01-16-2021, 12:30 PM
|
#2
|
Gone Traveling
Join Date: Feb 2016
Location: Texas
Posts: 1,392
|
You shouldn't need to find the controls to synchronize.
Extend the slide 3 to 5 inches, retract while being the button 3-5 seconds after completely sealed, repeat 3 to 5 times, then every time you extend/retract hold the button 3-5 seconds when completely in/out.
|
|
|
01-16-2021, 12:42 PM
|
#3
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
I need the location of the controllers I am doing work that requires me to unplug the motors from the controllers
|
|
|
01-16-2021, 12:57 PM
|
#4
|
Site Team
Join Date: Dec 2007
Location: WI.
Posts: 9,153
|
|
|
|
01-16-2021, 01:16 PM
|
#5
|
Seasonal Camper
Join Date: Feb 2017
Location: Michigan
Posts: 271
|
I have a different model TT, but my living room and kitchen slide controllers are in the entertainment center cabinet, bottom compartment, mounted on side wall.
__________________
2016 F 250 XLT 4x4 SC
2014 Sunset Trail Reserve ST26RB
|
|
|
01-16-2021, 02:42 PM
|
#6
|
Site Team
Join Date: Sep 2012
Location: PA
Posts: 5,715
|
Synchronizing the Slide-Out Motors
Motors and Harnesses
1. Check for proper connections between the motors and harnesses (Fig. 17).
2. Visually inspect the exposed harnesses to make sure they are not pinched or damaged.
Note: Ribs on motor connector line up with notch inside of female connector on wiring harness. Color
codes on wires also match (black to black, red to red, etc.).
Synchronizing the Slide-Out Motors
1. Fully extend the slide room using the switch. Keep the switch engaged until the motors shut down on
their own.
2. Retract the room 1-2 inches.
3. Repeat steps 1 and 2 until both motors shut down at the same time. In many cases, two or three
repetitions are necessary to synchronize the system.
4. Fully extend the slide-out and keep the switch engaged until the motors shut down on their own.
Fully retract the slide-out, again keeping the switch engaged until the motors shut down on their own.
If both motors shut down at the same time at full extension and full retraction, the room is properly
synchronized. If they do not shut down at the same time, repeat the process until they do.
Extend and Retract Switch Connection
1. Rev. A - Rev. C1 Controllers: Common connection on controller goes to common connection on extend
and retract switch.
2. Rev. C2 and 8 amp Controllers: Extend and retract connections on the controller go to the extend and
retract terminals on the switch. Switch is powered by the OEM-supplied 12V DC power source.
Power and Ground Connections at The Controller
Power and ground connections are supplied to the controller through the spade terminals located on the
right-hand side of the controller (Figs. 2 and 5 - Power Connection). 12V DC is recommended. A 10 AWG wire
is the minimum size recommended. A 30 amp, OEM-supplied resetting or blade fuse is require
__________________
Mark & Susan
Lehighton, Pennsylvania
EAGLE HT FIFTH WHEEL | 30.5CKTS - '13 Ford F150 SCREW - PullRite Superslide - Roadmaster Active Suspension
Member - "Northeast Adventures RV Rally Group" & "Mason-Dixon Bunch"
|
|
|
01-16-2021, 03:23 PM
|
#7
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
Thanks mark I need the location in the camper were the controllers are so I can unplug the motors from the controller. I know it's a small white box and I found the one for the bedroom but I need the location of the controllers that are in the living area were the fireplace is on one side and the dinette on the other side .
|
|
|
01-16-2021, 04:40 PM
|
#8
|
Seasonal Camper
Join Date: Feb 2017
Location: Michigan
Posts: 271
|
Bobby, check every cabinet in you TT. On mine they are not visible by opening the door. I had to literally stick my head into the cabinet to find them, mine are not in a very friendly location.
__________________
2016 F 250 XLT 4x4 SC
2014 Sunset Trail Reserve ST26RB
|
|
|
01-16-2021, 05:25 PM
|
#9
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
Ok I have tried looking in every cabinet I was hoping somebody had a 2013 or 14 32rl that knew were they was put
|
|
|
01-17-2021, 01:52 AM
|
#10
|
Site Team
Join Date: Jan 2014
Location: VA
Posts: 1,715
|
In my Sunset Trail, they are located in the entertainment center above the power distribution center. Behind the right hand cabinet door at the bottom is a panel. My controllers are behind that panel.
__________________
2013 Silverado 2500HD LTZ CC 6.6L Duramax Diesel
2023 Rockwood 2445WS
Buster, miniature Dachshund
2023: 9 trips, 48 nights in 12 states, 2 provinces, 8120 miles
2022: 3 trips, 18 nights in 4 states, 2352 miles
2019: 7 trips, 43 nights in 6 states, 5336 miles
|
|
|
01-17-2021, 06:38 AM
|
#11
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
I will check there I have the one that the tv turn to the outside to . I looked everywhere by the fire place at the bottom in both doors and at the top by the radio cd player. . Did you have to cut the panel or was it already made to access. I think if I am correct my power distribution panel is under the drawer beneath the refrigerator. .
|
|
|
01-18-2021, 02:13 AM
|
#12
|
Site Team
Join Date: Jan 2014
Location: VA
Posts: 1,715
|
My panel had screws holding it in place.
__________________
2013 Silverado 2500HD LTZ CC 6.6L Duramax Diesel
2023 Rockwood 2445WS
Buster, miniature Dachshund
2023: 9 trips, 48 nights in 12 states, 2 provinces, 8120 miles
2022: 3 trips, 18 nights in 4 states, 2352 miles
2019: 7 trips, 43 nights in 6 states, 5336 miles
|
|
|
01-20-2021, 04:24 PM
|
#13
|
Family Vacation Member
Join Date: Sep 2019
Location: SK
Posts: 180
|
I have found them in different places on the same model of TT. All depends who is doing the install that day.
Check below your fuse/breaker panel. Is there a small wood panel there with a screw in each corner? That is finally where I found mine.
check for removable panels (screws) below your switches. The wiring will go to floor then branch out. Usually they put the 2 controllers in the same location. And usually right where the wiring should split to either slide.
However that would mean the installer has common sense....
__________________
2014 29MK
Victron Energy inverter/charger, 1240w solar
550ah LifePo4, Microair Easy Start,RVLocks (keyless)
Airborne Elite Sidewinder pin, Maxx air 7500 Fan
2015 GMC LTZ,6.2 Gas, Short Box, Firestone F3 air ride.
Bilstein Shocks
|
|
|
01-20-2021, 04:42 PM
|
#14
|
Weekend Camper
Join Date: Jan 2021
Location: Tennessee
Posts: 10
|
Thank you to everyone for your help I located them beside the frig in a cabinet above the power supply converter
|
|
|
|
Thread Tools |
Search this Thread |
|
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Threads |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|