Forum: Cruiser
08-09-2011, 02:29 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
08-03-2011, 04:31 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
08-02-2011, 04:09 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
08-01-2011, 02:44 AM
|
Replies: 61
Views: 12,573
Today I rechecked the pin box movement with the...
Today I rechecked the pin box movement with the same technique of using a bottle jack in the truck bed and the laser sitting on a ladder. The number was slightly better than what I quickly measured...
|
Forum: Cruiser
07-31-2011, 06:46 AM
|
Replies: 61
Views: 12,573
Hank,
Yes, I saw him install the "L"...
Hank,
Yes, I saw him install the "L" brackets. I left before the special countersunk screws were put in because the dealer had to go purchase them. But the Lippert tech explained that they had...
|
Forum: Cruiser
07-31-2011, 02:00 AM
|
Replies: 61
Views: 12,573
Lippert dispatched their welder and he did a...
Lippert dispatched their welder and he did a great job. Lippert is still responsible for the frame warranty since they have done all the work. I believe this was the first repair at a dealer's...
|
Forum: Cruiser
07-30-2011, 10:29 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-30-2011, 10:07 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-29-2011, 01:33 PM
|
Replies: 61
Views: 12,573
Manufacturers don't have infinite knowledge,...
Manufacturers don't have infinite knowledge, sometimes it really takes customer feedback for a manufacturer to both recognize an issue and understand it. For example the Toyota sudden acceleration...
|
Forum: Cruiser
07-28-2011, 11:18 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-25-2011, 08:58 AM
|
Replies: 61
Views: 12,573
rcflyer,
I thought I addressed your concern...
rcflyer,
I thought I addressed your concern with an earlier post when I said.
"You are right there is some affect due to spring sag when comparing to an external reference point. But using your...
|
Forum: Cruiser
07-25-2011, 01:02 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-22-2011, 08:43 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-22-2011, 06:11 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-22-2011, 03:24 AM
|
Replies: 61
Views: 12,573
Matt,
Thanks for taking this data on...
Matt,
Thanks for taking this data on a newer unit. The 3/4" you measured to the clearance light is exactly what I measured and reported on June 14th. And the bedroom floor flex of 1/2" is...
|
Forum: Cruiser
07-21-2011, 09:28 AM
|
Replies: 61
Views: 12,573
Jerry,
In my original post, my...
Jerry,
In my original post, my measurement #1 was to an external fixed point. In my case, I used two steel studs suspended horizontally between posts in my RV port. Another option would be...
|
Forum: Cruiser
07-21-2011, 12:45 AM
|
Replies: 61
Views: 12,573
Lloyd,
While it would help to have...
Lloyd,
While it would help to have everyone make the same measurements for ez comparison, I think all the results so far are meaningful. Putting the laser further toward the rear of the trailer...
|
Forum: Cruiser
07-19-2011, 06:07 AM
|
Replies: 61
Views: 12,573
rcflyer,
Thank you for the effort...
rcflyer,
Thank you for the effort you have taken on this. You are right there is some affect due to spring sag when comparing to an external reference point. But using your 7/32 inch drop...
|
Forum: Cruiser
07-19-2011, 02:39 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-18-2011, 09:28 AM
|
Replies: 61
Views: 12,573
Here is a way to measure flex in the bedroom...
Here is a way to measure flex in the bedroom floor structure that is very EZ to do. Took less than 20 min. including taking the pictures.
The first picture shows the target, a piece of 1/8...
|
Forum: Cruiser
07-16-2011, 12:31 PM
|
Replies: 61
Views: 12,573
Clif,
Thanks for taking the...
Clif,
Thanks for taking the measurement, that 1/2 inch is pretty good, several of us have measured closer to 1 inch by a similiar technique. This is an ez measurement, but you did hit upon...
|
Forum: Cruiser
07-09-2011, 06:37 AM
|
Replies: 61
Views: 12,573
|
Forum: Cruiser
07-09-2011, 04:37 AM
|
Replies: 61
Views: 12,573
Is there anyone on the forum willing to try...
Is there anyone on the forum willing to try making this measurement??? Send me a PM if you would like more assistance or call me at: 512-663-9507.This would be helpful to new Cruiser owners. Harbor...
|
Forum: Cruiser
07-07-2011, 04:44 AM
|
Replies: 61
Views: 12,573
|